NuWell 410 Chlorine Enhancer

  Home    About Us    Contact Us    Used Rigs    My Account    My Cart  
Top > Well Supplies > Water Well Maintenance | Clean & Disinfect > NuWell 410 Chlorine Enhancer
<< Prev   Category 10 of 12   Next >> << Prev   Product 9 of 10   Next >>

NuWell 410 Chlorine Enhancer


SKU: NU410
PRICE: 104.95

NuWell 410 Chlorine Enhancer Description

DESCRIPTION
- Used with hypochlorite to increase effectiveness of chlorination
- Maintains pH in well at 6.5 during chlorination, increasing hypochlorus acid
- Increases bacteriological activity by more than 100 times that of hypochlorite
- Contains a penetrant to allow deeper and more complete disinfection
- Controls calcium in hard water to increase the effectiveness of calcium hypochlorite
- NSF certified for potable water well use

 

APPLICATION
Laboratory testing and field trials demonstrate that successful well chlorination is achieved with a chlorine concentration of 200 ppm. The following procedures are recommended for using Nu-Well 410 chlorine enhancer with chlorine concentrations of 200 ppm.


1. Determine the static volume, the amount of Nu-Well 410 chlorine enhancer and the amount of chlorine product necessary to treat the well according (Consideration should be given to increasing this volume by two to four times to allow sufficient disinfectant solution to reach all areas of the well and borehole that can harbor coliform bacteria or other contaminating organisms.)
2. In a tank on the surface, add the amount of Nu-Well 410 chlorine enhancer to water as estimated from dosage guide. Mix the solution; and measure the pH. The pH of the solution should be between 4.5 and 5 before adding the hypochlorite. All mixing should be done in a well-ventilated area. Caution: When chlorine is placed in an acid pH of 5.0 or lower, chlorine gas can be released. When the hypochlorite solution or powder is added, the pH will rise immediately, preventing any further chlorine release, but you should add the hypochlorite quickly and move away until the pH rises.
3. Place the chlorine solution in the well, evenly washing down the upper levels of the well before you place the solution throughout the water column
4. Agitate or surge the mixture to ensure good coverage. Let the solution stand in the well for 5 to 12 hours. Additional agitation before removal is beneficial. Nu-Well 410 chlorine enhancer is buffered to hold the pH at the optimal level. However, if additional Nu-Well 410 chlorine enhancer is required, blend in a volume equal to 25 percent of the original mixed volume and add carefully so that the pH does not drop below 5.0, resulting in release of chlorine gas.
5. Pump the solution to the surface, neutralize using Nu-Well 500 Chlorout, and discharge in accordance with local rules and regulations.

PHYSICAL PROPERTIES, SHIPPING AND HANDLING
Appearance: Clear, light amber liquid
Density: 9.3 lbs./gal.
pH (as shipped): 2.4 - 3.4
Specific Gravity: 1.12
Freeze point: 26 °F (-3 °C)
Solubility (in water): 100%
Use range: 0.01 to 1% by volume
Volatility: Non-volatile
- This product is not considered dangerous and does not require special handling or disposal
- Avoid contact with strong acids or alkaline-based products
- Not regulated as a hazardous material under 49CFR 172.101, RECRA, SARA and CERCLA
- 1 gal. and 5 gal. containers can be shipped by UPS ground delivery
- Additional physical and handling data are available on the product MSDS
- Nu-Well 410 chlorine enhancer is available in 1 & 5 gal. containers

 
Choose Options
Size 
Quantity:
Item Message:


Email To Friend





About Us
| Contact Us | Used Rig Bulletin Board | Home | My Cart

©2013 Environmental Service Products